Print

Promotional products / new items

Promotional products / new items

Display per page
Sort by

AX2

Product no.: AX2

AX2 MINATURE 20-METER WHIP ANTENNA.

 

The AX2 is small enough to take anywhere - just in time for light outdoor use during the new solar cycle. Use it HT-style with a handheld tripod like the KX2, on a picnic table with an AXB1 whip tripod, or with a camera tripod and the AXT1 tripod adapter. The AX2's rugged nylon housing is waterproof, wind resistant and features our new anti-wobble design.

Experimenters will appreciate the AX2's versatile design. A removable cover allows access to the high-Q inductor. Simply remove the windings and re-solder a wire to cover your favorite ribbon. Clip-off tabs are provided for ribbon identification.

SPECS

Resonant Frequencies    AX2: ~14 MHz (20 m) AXE1: ~7.2 MHz (40 m) Resonant frequencies may vary +/- 400 kHz or more due to variations in terrain,antenna

height, body capacitance, and length of radial(s).

Supplied Radial Wire      AX2: 13 ft. (4 m). AXE1: 33 ft. (10 m). Includes spade lug.

Max. Power                        15 Watts. If RFI symptoms are observed, reduce power or move the antenna farther from the transceiver.

Construction                      Corrosion-resistant whip and hardware; Lexan outer tube; high-Q inductors using #20 AWG high-temp enamel wire.

Dimensions (approx.)     Whip: 6” (15 cm) collapsed, 45” (115 cm) extended. Base unit: 2.5” (6 cm). AXE1 extender: 6” (15 cm).

Weight                                 AX2: 3.2 oz. (90 g). AXE1: 2.0 oz. (55 g).

 

98.00 *
Shipment:
innerhalb 14-21 Tagen lieferbar

New frontpanel set (front- and backside) for ZM4 ATU kit

Product no.: ZM4front

engraved and drilled front panel set (front and back) for ZM-4 ATU 160-10m from QRPproject

material: AL - 1 mm

surface: matt black anodized

from BaMaTech Feinmechanik

The ZM4 kit is not included !

18.50 *
Shipment:
innerhalb 14 Tagen lieferbar

SDT21 Band Set 40m

Product no.: SDT21 BS40m

Set of band specific parts to complete the SDT21 basic kit to a complete 40m monoband TRX!

 

 can only be ordered together with a SDT21 basic kit!

0.00 *
Shipment from Stock: 20

New SDT21 simple digital transceiver

Product no.: SDT21

simple "digital" monoband transceiver SDT21

 

The goal of this project was the development of a simple to build CW monoband transceiver based on the direct superheterodyne principle with crystal control a la "PIXIE" or "Rockmite", but with much better technical data. To minimize the circuit effort, the concept should be as highly integrated as possible and realizable without hand-wound coils. Furthermore, for the SMD phobics, SMD placement was completely omitted this time. Despite these specifications, it was possible to fit the entire circuit on a double-sided PCB with dimensions of 69x52mm, which allowed it to be installed in the small TEKO A2 package.

The main focus of the circuit is based on the little known fact that digital inverters or gate devices of the 4000 CMOS series can be operated as analog amplifiers by a circuit trick, important here is the use of the unbuffered IC variant (index UB).

 

Please order the desired "set of band specific parts" according to the desired frequency!

49.00 *
Shipment from Stock: 12

Schurr-Profi M

Product no.: Schurr-Profi M

Schurr Profi M by Stefan Bergsiek

Schurr-Profi M

Stainless steel polished V2A Niro

Dimensions 100x80x28mm

Special edition stainless steel

 

The paddles are mounted backlash-free with hardened cylindrical pins in brass plain bearings. Due to this connection the bearing is absolutely maintenance-free! The advantage of this paddle bearing is that, unlike a ball bearing, no gumming up can occur over the years and the bearing can fail or become stiff. Any adjustment of this paddle bearing is not necessary.

Hard silver contacts as well as fine thread are standard.

319€ Christmas offer

369.00 *

Spare cover for Schurr Profi 2 and Profi 3

Product no.: SchurrHaube

Spare cover for Schurr Profi 2 and Profi 3

25.00 *
Shipment:
innerhalb 7-21 Tagen lieferbar

SOTA Schurr Wabbler designed by Stefan Bergsiek

Product no.: SotaWabbler

SOTA Schurr Wabbler by Stefan Bergsiek

small portable key from Schurr / Bergsiek

gold plated

about 170g

No springs are installed. The paddle reset is made by magnets

The paddles are mounted without play with hardened cylinder pins in brass sliding bearings. Due to this connection, the bearings are absolutely maintenance-free! The advantage of this paddle bearing is that, unlike a ball bearing, no hardening over the years can occur and thus the storage can fail or become difficult. Any adjustment of this paddle bearing is not necessary.

Hard silver contacts as well as fine threads are normal standard.

The key is delivered with a 1.5 m long high-quality cable and 3.5 mm jack plug-in connector.

The key is made of full brass

Can also be installed as a replacement mechanism in an old ETM

 

preorders are now accepted

189.00 *
Shipment:
innerhalb 14-28 Tagen lieferbar

KX3 desk stand

Product no.: KX3deskstand

desk stand for the KX3

 

from Stefan Bergsiek

29.00 *
Shipment from Stock: 18

PX3 desk stand

Product no.: PX3deskstand

desk stand for the PX3

 

from Stefan Bergsiek

26.00 *
Shipment from Stock: 6

K2_keyout

Product no.: K2_keyout
15.00 *
Shipment from Stock: 8

TCXO SO1-NG for Kenwood TS930

Product no.: TCXO SO1-NG for TS930

The new high precision SO1-NG TCXO replacement for the Kenwood TS930 transceivers

This board is a aftermarked replacement for the Kenwood SO-1 TCXO UNIT, which is no longer available as original spare part.


The specifications:

- Output frequency: 20MHz
- Frequency stability: +-0,5ppm (or with extra high stability option: ±0,14ppm)
- Operating Temperature Range: -20 to 70°C
- Frequency tuning range: 200Hz
- Power supply requirements: 4,5 to 28 VDC, max. 3mA

 

if you want the extra high stability, please add "TXCO high stability" to your order

70.00 *
Shipment:

TCXO SO1-NG for Kenwood TS940

Product no.: TCXO SO1-NG for TS940

The new high precision SO1-NG TCXO replacement for the Kenwood TS940 transceivers

This board is a aftermarked replacement for the Kenwood SO-1 TCXO UNIT, which is no longer available as original spare part.


The specifications:

- Output frequency: 20MHz
- Frequency stability: +-0,5ppm (or with extra high stability option: ±0,14ppm)
- Operating Temperature Range: -20 to 70°C
- Frequency tuning range: 200Hz
- Power supply requirements: 4,5 to 28 VDC, max. 3mA


 

if you want the extra high stability, please add "TXCO high stability" to your order

70.00 *
Shipment:

TCXO SO1-NG for Kenwood TS50, TS850, TS870, TS690, TS570D, TS950, TS450

Product no.: TCXO SO2-NG

The new high precision SO2-NG TCXO replacement for the Kenwood TS50, TS850, TS870, TS690, TS570D, TS950 and TS450 transceivers

This board is a aftermarked replacement for the Kenwood SO-2 TCXO UNIT, which is no longer available as original spare part.


The specifications:

- Output frequency: 20MHz
- Frequency stability: +-0,5ppm (or with extra high stability option: ±0,14ppm)
- Operating Temperature Range: -20 to 70°C
- Frequency tuning range: 200Hz
- Power supply requirements: 4,5 to 28 VDC, max. 3mA
 

if you want the extra high stability, please add "TXCO high stability" to your order

70.00 *
Shipment:

TCXO extra high stability with ±0,14ppm

Product no.: TCXO high stability

Option for extra high stability if required please order separately.

only in combination with TCXO SO1-NG / TCXO SO2-NG


- Frequency stability: ±0.14ppm

79.30 *
Shipment:

AXE1 40m extender for AX1 Antenna

Product no.: AXE1

AXE1 40m extender

 

extension to use  the AX1 Antenna on 40m and 30m (internal ATU needed!)

 

delivery include:

40m extension coil (15cm)

radial wire (10m)

73.00 *
Shipment:
innerhalb 14-21 Tagen lieferbar

vFSW

Product no.: vFSW
29.00 *
Shipment:
innerhalb 14 Tagen lieferbar

vAktivantenne

Product no.: vAktivantenne
58.00 *
Shipment from Stock: 1

GehäuseWRFM

Product no.: GehäuseWRFM
6.00 *
Shipment from Stock: 2

WRFM

Product no.: WRFM
65.00 *
Shipment from Stock: 3

QCD-70

Product no.: QCD-70
12.00 *
Shipment from Stock: 5

SDT21 Band Set 30m

Product no.: SDT21 BS30m

Set of band specific parts to complete the SDT21 basic kit to a complete 30m monoband TRX!

 

 can only be ordered together with a SDT21 basic kit!

0.00 *
Shipment from Stock: 11
*
Prices incl. VAT, plus delivery