K3S Kit

K3S Kit



Display per page
Sort by
1 - 30 of 36 results

Product no.: MH4
86.00 *

innerhalb 7-14 Tagen lieferbar

Product no.: K-POD

K•Pod Control Panel for the K3S & K3


Precision, Weighted Tuning Knob

16 Programmable Switch Functions

USB Port for Firmware Upgrades, Future Expansion

3 Utility Outputs


A Compact Accessory Panel for Contesting, DXing, and Customized Station Control

Our new K-Pod is the ideal companion to your Elecraft K3 or K3S Transceiver, maximizing both convenience and operating efficiency. At only 3.5 x 3 x 1 inches (9 x 7.5 x 2.5 cm), it can be placed anywhere the action is, typically next to a computer keyboard. It’s versatile enough to integrate transceiver and station control functions, putting you in command as never before.


A utility jack beneath the radio’s front panel acts as the K-Pod’s data interface. The unit can be powered from the radio’s rear 12-V accessory output, the pod’s own USB port, or any 8-15 V, 50-mA DC power source.


now preorder possible

360.00 *

innerhalb 14-21 Tagen lieferbar

Product no.: KAT3A
495.00 *
Product no.: KBPF3A
245.00 *
Product no.: K144XV
580.00 *

innerhalb 14 Tagen lieferbar

Product no.: K3EXREF
135.00 *
Product no.: NEOGRIP
25.00 *

innerhalb 14 Tagen lieferbar

Product no.: KXV3B
275.00 *
Product no.: SS30DV
150.00 *

innerhalb 14 Tagen lieferbar

Product no.: SP3

SP3 Matching External Speaker

High Performance Matching Speaker for the K3S & K3 designed by audio expert Dr. Bruce Edgar (link to article on Bruce). Two rear inputs with front panel switch for selecting between different radio sources and a rear output jack for a adding a second speaker (stereo)


250.00 *

innerhalb 14 Tagen lieferbar

Product no.: SP3_2nd
245.00 *

innerhalb 14 Tagen lieferbar

Product no.: K3SHandbuch
55.00 *

Shipment from Stock: 999,999

Product no.: KPA3A
K3 100 W PA for an allready existent K3. Allready assembled, solderfree mounting.
700.00 *
Product no.: KRC2

The Elecraft KRC2 Band Decoder is a universal, programmable station control unit that can switch any combination of antennas, filters, amplifiers, or other equipment. It supports analog, digital, and RS232 control inputs

220.00 *

innerhalb 14 Tagen lieferbar

Product no.: Schaltnetzteil 23A
Switched Powersupplyl 23A, 25A Peak special design for Radio applications. Extrem low noiselevel ar RF Frequencies.Best for Elecraft K2/100, K3 and other Transceivers.
Input: bis 240 V~ 50 Hz
Out: 13,3 - 14,5 V DC (can be adjusted)
Cooled by big Aluminiumbloc Internal Low Noise Fan, only activ in high duty situations.

Enclosure: Steel black
181x63x190 1,7 Kg
CE, EN 60960, EN 55022.
109.00 *

Shipment from Stock: 7

Product no.: KSYN3AUPG

ATTENTION: Due to the high number of orders, our stock is empty. New KSYN3A will be available again early in April 2015

KSYN3A Synthesizer Upgrade Kit for K3, KRX3 (Note: Synthesizers used for the K3 and the KRX3 must both be the same model. K3's with the KRX3 will need to upgrade both (2 total) synthesizers to the KSYN3A.)

The KSYN3A is included on all new K3s shipped starting 1/23/2015, s/n 8801 and later.

The KSYN3A synthesizer module is a completely new design that improves on the original KSYN3 in several ways:

ULTRA-LOW PHASE NOISE The KSYN3A significantly improves the K3's already excellent RX and TX phase noise at close carrier spacings. This in turn noticeably improves the K3's top performing close spaced Rx dynamic range, yielding even better weak signal detection in the presence of strong signals.


EXCELLENT MECHANICAL STABILITY The KSYN3A is virtually immune to both physical vibration and magnetic coupling, and operates over a very wide temperature range.

600-METER COVERAGE The KSYN3A extends VFO tuning down to 100 kHz, with sensitivity gradually falling off below 450 kHz. Transmit output is as high as 1.0 mW for use with a suitable external amplifier. (Note: 600-m and below operation also requires the KBPF3 and KXV3 options.)

375.00 €
375.00 *
Product no.: VSUBD15
1.90 *

Shipment from Stock: 2

Product no.: P3-K
The new P3 Panadapter display adds a visual dimension to signal hunting with fast real time spectrum and waterfall displays of band activity. The P3 offers superior sensitivity and DSP processing, giving you the ability to see signals down to the K3's noise floor.
970.00 *
Product no.: P3SVGA
360.00 *
Product no.: P3TXMON

TX  Monitor Power and Waveform Display Adapter for the P3   


at least you need one directional coupler, which have to choosen seperately.

- coupler for 0.1-200 W 1-54 MHz (DCHF-200)

coupler for 1-2000W 1-54 MHz (DCHF-2000)

coupler for 1-200W 144-450 MHz (DCV/U-200)

260.00 *
Product no.: DCHF-2000
0.00 *

innerhalb 14 Tagen lieferbar

Product no.: DCHF-200
0.00 *

innerhalb 14 Tagen lieferbar

Product no.: DCV/U-200
0.00 *

innerhalb 14 Tagen lieferbar

Product no.: CBLP3Y
50.00 *


Product no.: P3Handbuch
50.00 *

Shipment from Stock: 999,999

Product no.: proset-K2
205.00 *

innerhalb 14 Tagen lieferbar

Product no.: SLK3KabelVV
SignalLink cable to connect an Elecraft K3
20.00 *

Shipment from Stock: 3

Product no.: KUSB3
15.00 *
Product no.: MC43mikro
42.00 *


Product no.: Vbalun100
Balun 1:4 100Watt, ReadyBuilt. Connected to asymetric ATU by PL/PL adapter (included)
47.00 *

Shipment from Stock: 1

Prices incl. VAT, plus delivery
1 - 30 of 36 results