Product no.: SMA-BNC
Adapter cable RG316 with SMA male to BNC female. 15cm long pigtail. |
11.00 €
*
Shipment from Stock: 31 |
|
Product no.: cdm |
10.00 €
*
Delivery time: please ask by email |
|
Product no.: QRPPA2008
The new PA needs 10mW drive to produce a clean and linear amplified signal of 10 Watts RF Speciefier Frequency rage: 1-30 MHz.
The VMOS we use could give us more the 15 Watt, but we desided to stay with the traditional 10 Watt border for SSB QRP which also gives a more clean output by avoiding any overdriving. The PA is a Push Pull design. We use the modern Mistubishi RD06HHF as driver and a pair of RD16HHF as push pull PA. Quiescent current is adjusted for any of the 3 single transistors which results in absolute stable working conditions. The PCB is as small as 55mm x 40mm, so it´s a good chance to fit into any homebrew project like standard transceivers or SDR. It is mounted on two metall standoffs, the 3 Transistors will be screwed to the backplane of the enclosure. |
52.00 €
*
Shipment: |
|
Product no.: Einsteigerklein
Starter Set as package. Small Signal Generator (equipped with an Xtal of Your choice) calibrated HF/AF probe, Power Noise Generator |
79.00 €
*
Shipment: |
|
Product no.: SWRAufbau
assembling service for the kit vSWRK by QRPproject. all SNT parts and the wireing of the mini torroid. the kit vSWRK is not included and must ordered in addition!
|
11.00 €
*
Shipment from Stock: 999,999 |
|
Product no.: VPWRRgenSMD
Service: all SMT parts prinstalled by QRPproject
|
12.00 €
*
Shipment from Stock: 999,999 |
|
Product no.: HerfordZaehler
Small Pic based counter for small rigs. Upper limit is 50 MHz, IF Offset programmable. Display onl 33mm(h) x 52mm (w) Below 10MHz resolution is 100Hz, above 10 MHz resolution 1kHz
|
35.00 €
*
Shipment: |
|
Product no.: Schaltnetzteil 23A
Switched Powersupplyl 23A, 25A Peak special design for Radio applications. Extrem low noiselevel ar RF Frequencies.Best for Elecraft K2/100, K3 and other Transceivers.
Input: bis 240 V~ 50 Hz Out: 13,3 - 14,5 V DC (can be adjusted) Status-LED Cooled by big Aluminiumbloc Internal Low Noise Fan, only activ in high duty situations. Enclosure: Steel black 181x63x190 1,7 Kg CE, EN 60960, EN 55022. |
109.00 €
*
Shipment from Stock: 7 |
|
Product no.: AF1
* Filters: Variable Cutoff Low pass filter (SSB/CW) plus two levels of narrow CW bandpass filtering with tunable center frequency. |
110.00 €
*
Shipment: |
|
Product no.: UG-306U
BNC Male-Female Right Angle Adapter
|
2.50 €
*
Shipment from Stock: 16 |
|
Product no.: Vpk4erg
PK4 Keyer Add On: Small plastic enclosure with Batterie Compartment (9V Baterie), Potentiometer, 3,5mm Stereo Jacks, Knob. Piezo
|
12.00 €
*
Shipment from Stock: 1 |
|
Product no.: Vpk4
PK4 Keyer kit Jackson Habor Press
|
29.00 €
*
Shipment: |
|
Product no.: VUniRit |
15.00 €
*
Shipment from Stock: 2 |
|
Product no.: XG3
XG3 RF Signal Source (assembled) 1.5-200 MHz with calibrated output levels: -107, -73, -33 and 0 dBm. Rich in harmonics to 1400 MHz. Frequencies programmed into memories above 200 MHz fundamental will automatically calculate the fundamental needed to generate the desired harmonic. 12 frequency memories, computer controllable. |
330.00 €
*
Shipment from Stock: 1 |
|
Product no.: W1
140W - Wattmeter and SWR Bridge Brücke incl. Data-Port. Frequency - Range:h 1,8 - 30 MHz |
160.00 €
*
Shipment from Stock: 1 |
|
Product no.: AT1
AT1 Attenuator 40 dB Range: 0 to 41 dB 1 dB Steps |
75.00 €
*
Shipment: |
|
Product no.: DL1
Elecraft 25W Dummy Load 50 Ohm
|
42.00 €
*
Shipment: |
|
Product no.: SotaWabbler
SOTA Schurr Wabbler by Stefan Bergsiek small portable key from Schurr / Bergsiek gold plated about 170g No springs are installed. The paddle reset is made by magnets The paddles are mounted without play with hardened cylinder pins in brass sliding bearings. Due to this connection, the bearings are absolutely maintenance-free! The advantage of this paddle bearing is that, unlike a ball bearing, no hardening over the years can occur and thus the storage can fail or become difficult. Any adjustment of this paddle bearing is not necessary.
preorders are now accepted |
169.00 €
*
Shipment: |
|
Product no.: SchurrHaube
Spare cover for Schurr Profi 2 and Profi 3 |
25.00 €
*
Shipment: |
|
Product no.: Schurr-Profi M
Schurr Profi M by Stefan Bergsiek Schurr-Profi M Stainless steel polished V2A Niro Dimensions 100x80x28mm Special edition stainless steel
The paddles are mounted backlash-free with hardened cylindrical pins in brass plain bearings. Due to this connection the bearing is absolutely maintenance-free! The advantage of this paddle bearing is that, unlike a ball bearing, no gumming up can occur over the years and the bearing can fail or become stiff. Any adjustment of this paddle bearing is not necessary. Hard silver contacts as well as fine thread are standard. 319€ Christmas offer |
369.00 €
319.00 €
*
|